Additives

Add contents to the cooling water. Turn the heating to maximum and let the engine run on idle for 10 - 30 minutes depending on the degree of contamination. Drain the coolant and flush the cooling system with water. Fill the cooling system according...

To prepare, attach tube with nozzle. To gain access, remove hose or pipe immediately before throttle housing. The engine needs to run to perform cleaning. If unable to start engine, disconnect air mass sensor connector while the ignition switch is in off position. Maintain...

Contents sufficient for max. 5 liters (5.28 U.S. QT) of motor oil, minimum filling of 3 liters (3.17 U.S QT) is requested for optimum product performance. The product is self mixing and can be added at any time, sealing first takes effect after about...

MoS2 Anti-Friction Engine Treatment ensures immediate friction and wear reduction, adds an extremely protective and pressure-resistant boundary layer with low friction and lubricates during cold starts to prevent damage from lack of oil. Contributes to lower fuel consumption, longer engine life and less noise....

Motul 300ml Engine Clean Auto Additive

HiTest is a concentrated, metal-free octane booster designed to increase power by increasing octane number and combustion efficiency. The advanced formulation eliminates knocking by increasing the auto-ignition temperature of the air/fuel mixture and readily mixes with all fuels, including nitro and alcohol mixtures. The...

The unique combination of proven PEA technology and the latest additive generation achieves maximum cleaning performance in the combustion chamber, in and around the injector tip and in the entire fuel system. Furthermore, DIJectron stops the formation of new deposits so that complex injector...

Provides initial lubrication of new or replaced turbochargers to prevent damage due to oil starvation. Damage to turbocharger may occur within seconds of engine start if not lubricated properly. Pro-Line Turbocharger additive will provide needed protection and allow proper break-in of new units which...

One 500 ml can is sufficient for up to 5 liters(1.3 gal.) of oil. Add Pro-Line Engine Flush to the engine oil at operating temperature before changing the oil. After adding the product allow the engine to idle for 10 to 15 minutes depending...

To be added directly into the fuel tank. As a preventive measure, add during each inspection, after repairs on the fuel system and after each Jet-Clean cleaning operation. The product mixes with the fuel automatically. Minimum fuel filling of 25 liters (7 gal.) is...

A combination of agents, developed specifically for late model hybrid engines. Removes deposits in the fuel system and protects against corrosion. Stabilizes the fuel and protects against aging and oxidation. Diminished fuel degradation allows better engine performance and efficiency.

To be added directly into the fuel tank. Use aspreventive or to cure acute engine problems. The product mixes with the fuel automatically. Minimum fuel filling of 25 liters (7 gal.) is requested for optimum product performance. Contents of Can sufficient for max.115 liters...

High-tech fuel additive, developed specifically for improved throttle response under partial engine load. Optimizes fuel atomization and combustion, cleans fuel system while providing maximum engine performance and efficiency.

LIQUI MOLY recommends adding Motorbike Radiator Cleaner to the cooling water if problems arise or before changing the coolant. Depending on the level of contamination, run the engine at operating temperature for 10-30 minutes. Drain the cleaner and flush out the cooling system with...

One 300 ml can is sufficient for up to 75 liters (20 gal.) of fuel. Regular use keeps injection system in perfect working order and gives lowest exhaust emissions. Smoother idling, better throttle response. Injection Cleaner can be mixed with fuel at any time...

One 250 ml can is sufficient for minimum 3 liters(0.8 gal.) to maximum 4.5 liters(1.2 gal.) of oil. Add Motorbike Engine Flush to the motor oil atoperating temperature before changing the oil. After adding the product, allow the engine to idle for approx. 10...

A combination of additives to clean and maintain the diesel fuel system. Prevents corrosion, increases lubrication thus reduces fuel pump and injector wear. Increases Cetane value for improved engine performance, easier starting and lower emissions. Regular use keeps the fuel system in perfect working...

For all gasoline engines. Suitable for standard and high-octane gas, leaded and unleaded. 150 ml is sufficient for up to 75 liters (20 gal.)of fuel.Minimum fuel filling of 25 liters (7 gal.) is requested for optimum product performance.

One 300 ml can of Liqui Moly hydraulic tappet additive is sufficient for up to 6 liters (1.5 gal.) motor oil. The product can be added at any time. After adding, run the engine until warm. For a lasting effect, Liqui Moly Hydraulic tappet...

High-tech anti-wear additive, suitable for most 4-stroke engines as well as manual transmissions and compressors.Reduces friction and wear thanks to a unique combination of ceramic compounds and chemical anti-wear agents. It will prevent direct metal-to-metal contact and reduce friction to increase engine life and...